VFD 110V 2.2KW 2hp Nsakrae Frequency Drive CNC VFD Motor Drive Inverter Nsakrae ma CNC Spindle Motor

Zhong Hua Jiang 110V 2.2KW CNC VFD Inverter ma Spindle Motor

Saa Zhong Hua Jiang 110V 2.2KW CNC VFD inverter yi yɛ nea wɔayɛ ama abiɛsa phase 110V asynchronous CNC spindle motors. Ɛdannan single phase 110V input kɔ abiɛsa phase 110V output, na ɛma ɛfata ma CNC routers, engraving mfiri, nnua adwuma CNC mfiri, ne spindle ahoɔhare control nhyehyɛe.

VFD no boa 0-400Hz output frequency, MODBUS485 nkitahodi, Mach3 control, built-in breki unit nkitahodi, DSP vector control, 16-section ahoɔhare control, pii mfomso ahobammɔ, ne torque output kɛse wɔ ahoɔhare a ɛba fam. Wɔadi kan ayɛ ho nhyehyɛe ne mfitiase parameters na aboa wɔn a wɔde di dwuma no ma wɔawie nhyehyɛe no ntɛmntɛm.

Nneɛma Titiriw a Ɛwɔ Hɔ

• 110V 2.2KW CNC VFD inverter ma nea ɛne no hyia abiɛsa phase spindle motors.

• Single phase 110V input ne abiɛsa phase 110V output.

• Output frequency range fi 0-400Hz ma CNC spindle ahoɔhare sohwɛ.

• Pre-programmed mfitiase parameters ma ɛyɛ mmerɛw sɛ wobɛhyehyɛ.

• MODBUS485 nkitahodi ne Mach3 control mmoa.

• Wɔasisi breki unit ma tẽẽ breki resistor nkitahodi.

• DSP vector control ma torque a ɛkorɔn wɔ ahoɔhare a ɛba fam a ɛkyinkyini.

• 16-ɔfã ahoɔhare control ma flexible CNC machining adwumayɛ.

• Mfomso ahobammɔ pii ma ahobammɔ spindle nhyehyɛe adwumayɛ.

• Mframa dodow a ɛyɛ nwini fan kɛse a ɛwɔ ahofadi a ɛma ɔhyew a wɔsɛe no kwan.

Mfiridwuma mu Nneɛma a Wɔde Yɛ Nneɛma

• Aguade: CNC VFD inverter / Nsakrae Frequency Drive

• Tumi: 2.2KW

• Wɔakyerɛ sɛ: 2HP, 110V, 2.2KW

• Input ahoɔden: Single phase 110V

• Output voltage: Abiɛsa phase 110V

• Nsɛm a wɔde hyɛ mu: 50/60Hz

• Nneɛma a wɔde fi mu ba: 0-400Hz

• Motor a ɛfata: Abiɛsa phase 110V asynchronous CNC spindle motor nkutoo

• Ne kɛse: 90 × 118 × 150mm / 3.5 × 4.65 × 5.9 nsateakwaa

• Ne mu duru: 1.3kg / 2.87lbs

Aguade Ho Nkyerɛkyerɛmu

Pre-Programmed CNC VFD ma ɛyɛ mmerɛw sɛ wobɛhyehyɛ

Wɔadi kan ayɛ CNC VFD yi ho nhyehyɛe de mfitiase parameters, enti enhia sɛ wɔn a wɔde di dwuma no wie mfitiase nhyehyɛe a ɛyɛ den ansa na wɔayɛ adwuma. Default maximum frequency yɛ 400Hz, na wɔn a wɔde di dwuma no betumi asiesie frequency no sɛnea spindle RPM a wɔhwehwɛ no te.

Wɔayɛ no sɛ ɛwɔ phase baako input ne three phase output, na ɛma ɛfata ma adwumayɛbea ne CNC router dwumadiefoɔ a ɛhia sɛ wɔde three phase 110V spindle motor fi 110V power supply mu.

Breki Resistor Nkitahodi ne MODBUS485 Nkitahodi

Saa VFD yi boa Mach3 ne MODBUS485 nkitahodi dwumadie. Breki a wɔde ahyɛ mu no ma inverter no tumi kɔ breki resistor so tẽẽ, na ɛboa ma deceleration control ne spindle adwumayɛ a ɛyɛ den wɔ CNC machining applications mu no tu mpɔn.

Mframa Kɛse a Ɛma Nwini Fan

Fan a ɛma onwini no ma mframa dodow a ɛkɔ soro bɛboro 20% sen fan a ɛyɛ mpapahwekwa. Mframa a ɛma ɔhyew a ɛde ne ho a ɛwɔ VFD no mu no ma onwini a ɛtetew mu ba na ɛboa ma mfutuma ne nsu a ɛyɛ nwini nkɔ ɔmansin board no mu.

Mfomso Ahobammɔ Pii

Inverter no bi ne PID nhyehyɛe a wɔasisi, ahoɔhare akyi di, multi-function relay output, pii mfomso ahobammɔ, pii tebea feedback, torque control, ne analog nhyehyɛe. Saa dwumadie yi boa ma wɔbɔ VFD ne spindle motor ho ban wɔ CNC routing, engraving, ne machining adwumayɛ mu.

Torque a Ɛkorɔn wɔ Ahoɔhare a Ɛba Fam Rotation mu

DSP vector control ma spindle motor no tumi nya torque a ɛkorɔn bere a ahoɔhare a ɛba fam a ɛkyinkyini no. Dead zone akatua ne automatic torque nsonsonoe compensation betumi anya low frequency 0.25Hz ne 180% soro torque output ma ahwehwɛde CNC spindle applications.

16kHz Carrier Frequency a wotumi sesa

Carrier frequency no yɛ nsakraeɛ kɔsi 16kHz. Automatic voltage regulation mfiridwuma boa ma wɔhwɛ hu sɛ VFD adesoa tumi ne stable spindle motor adwumayɛ bere CNC machining.

Wiring Mfonini a ɛkyerɛ VFD

Wiring Diagram Ntam VFD ne Control Board

Saa VFD yi fa phase 110V asynchronous CNC spindle motors abiɛsa nkutoo ho.

Fa spindle motor no bata U / V / W terminals a ɛwɔ VFD no so no ho.

Dɛn na Ɛma Eyi 2.2KW CNC VFD Yɛ Soro?

• Wɔayɛ ama 110V 2.2KW CNC spindle motor ahoɔhare sohwɛ.

• Mfitiaseɛ parameters a wɔadi kan ayɛ ho nhyehyɛe boa ma wɔtew bere a wɔde hyehyɛ so.

• Breki resistor nkitahodi boa deceleration control a ɛyɛ den kɛse.

• DSP vector control de torque a ɛkorɔn ma wɔ ahoɔhare a ɛba fam a ɛkyinkyini mu.

• Mfomso pii ahobammɔ ma ahobammɔ tu mpɔn bere a CNC reyɛ adwuma.

• Independent cooling channel boa ma mfutuma ne nsuo a ɛwɔ mu no so tew.

• Ɛfata ma CNC router, CNC engraving, nnua adwuma, ne spindle motor nhyehyɛe.

Zhong Hua Jiang Brand ne Nneɛma a Wɔyɛ no Ho Nsɛm

Wɔde Huajiang sii hɔ wɔ afe 2000 mu, wofii ase yɛɛ CNC engraving spindle motors na akyiri yi wɔtrɛw adwumayɛ mu kɔɔ VFD variable frequency drives ne engraving mfiri ahorow so. Sɛnea ɛbɛyɛ a wɔbɛhwehwɛ na wɔanya wiase nyinaa gua pii no, wɔde Zhong Hua Jiang ahyɛnsode no sii hɔ wɔ afe 2018 mu.

Zhong Hua Jiang wɔ bere tenten mu osuahu wɔ CNC spindle motors ne VFD nneɛma mu, na ɔde nneɛma ma CNC router dwumadiefoɔ, mfiri adansifoɔ, wɔn a wɔkyekyɛ, ne B2B adetɔfoɔ wɔ amanaman ntam gua so.

Waranti ne Mmoa a Wɔde Ma

Esiane sɛ Zhong Hua Jiang wɔ bere tenten wɔ adwumayɛ mu osuahu wɔ CNC spindle motor ne VFD nneɛma mu nti, ɔde mmoa ma wɔ nneɛma a wɔpaw, wiring, nhyehyɛe, ne dwumadie ho nsɛmmisa ho. Sɛ wopɛ nneɛma pii a wɔkra, nea ɔkyekyɛ nneɛma, anaasɛ CNC spindle nhyehyɛe a ɛne ne ho hyia a, yɛsrɛ wo, di yɛn ho nkɔmmɔ na woanya nsɛm pii.

FAQ

Spindle motor bɛn na saa 2.2KW VFD yi ne no hyia?

Saa VFD yi fata nkutoo ma abiɛsa phase 110V asynchronous CNC spindle motors. Ansa na wode besisi hɔ no, yɛsrɛ sɛ si so dua sɛ spindle motor no ahoɔden, phase, ne ahoɔden no ne inverter no nkyerɛkyerɛmu no hyia.

So VFD yi betumi adan single phase 110V ayɛ no three phase 110V?

Aane. Saa VFD yi de single phase 110V input di dwuma na ɛma abiɛsa phase 110V output ma CNC spindle motors a ɛne no hyia.

So wɔadi kan ayɛ CNC VFD yi ho nhyehyɛe?

Aane. Wɔadi kan ayɛ VFD no ho nhyehyɛe a wɔde mfitiase parameters ahyɛ mu. Wɔn a wɔde di dwuma no betumi asiesie frequency no sɛnea spindle ahoɔhare a wɔhwehwɛ no te, na default maximum frequency no yɛ 400Hz.

So saa VFD yi boa Mach3 ne MODBUS485?

Aane. Saa inverter yi boa Mach3 control ne MODBUS485 nkitahodi, na ɛma ɛfata ma CNC router control board nkabom.

So VFD yi betumi akɔ breki resistor so?

Aane. VFD no wɔ breki a wɔde ahyɛ mu na wobetumi de abɔ breki resistor a ɛne no hyia tẽẽ ama deceleration control atu mpɔn.

CNC dwumadie bɛn na ɛbɛtumi de saa 2.2KW VFD yi adi dwuma?

Wɔtaa de di dwuma ma CNC routers, CNC engraving mfiri, nnua adwuma CNC mfiri, ne spindle motor nhyehyɛe afoforo a ɛhwehwɛ sɛ ɛsakra frequency ahoɔhare control.