VFD 110V 2.2KW 2hp Variable Frequency Drive CNC VFD Motor Drive Inverter Converter hmanga CNC Spindle Motor hman tur a ni

Zhong Hua Jiang 110V 2.2KW CNC VFD Inverter hmanga Spindle Motor hman theih a ni

He Zhong Hua Jiang 110V 2.2KW CNC VFD inverter hi phase thum 110V asynchronous CNC spindle motor atana siam a ni. Single phase 110V input chu three phase 110V output-ah a chantir a, hei hian CNC router, engraving machine, thinga siam CNC machine, leh spindle speed control system atan a tha hle.

VFD hian 0-400Hz output frequency, MODBUS485 communication, Mach3 control, built-in brake unit connection, DSP vector control, 16-section speed control, multiple fault protection, leh speed hniam takah torque output sang tak a support a ni. User te tan setup awlsam zawka tihfel theih nan basic parameters nen pre-programmed a ni.

Thil pawimawh tak tak

• 110V 2.2KW CNC VFD inverter hmangin phase thum spindle motor hman theih a ni.

• Single phase 110V input leh phase thum 110V output a awm bawk.

• CNC spindle speed control nan output frequency 0-400Hz inkar a ni.

• Installation awlsam zawk nan basic parameters pre-programmed a ni.

• MODBUS485 inbiakpawhna leh Mach3 control support a ni.

• Brake resistor direct connection atan brake unit dah tel a ni.

• Speed ​​hniam rotation-a torque sang tak neih theihna tur DSP vector control.

• CNC machining hmanga hnathawh theihna tur section 16-a speed control.

• Spindle system him zawka hman theih nan multiple fault protection.

• Air volume cooling fan lian tak, independent heat dissipation channel nei.

Technical Parameter hrang hrang te

• Thil siam chhuah: CNC VFD inverter / Variable Frequency Drive hmanga siam a ni

• A chakna: 2.2KW

• Rated specification: 2HP, 110V, 2.2KW te a ni

• Input voltage: Single phase 110V a ni

• Output voltage: Phase thum 110V a ni

• Input frequency: 50/60Hz a ni

• A chhuahna frequency: 0-400Hz a ni

• Motor hman tur: Three phase 110V asynchronous CNC spindle motor chauh

• A sei zawng: 90 × 118 × 150mm / 3.5 × 4.65 × 5.9 inches a ni

• A rih zawng: 1.3kg / 2.87lbs

Product Description chungchang

Setup awlsam zawk nan CNC VFD chu Pre-Programmed a ni

He CNC VFD hi basic parameters hmanga pre-programmed a nih avangin users te chuan operation hmain initial settings buaithlak tak tak an tih zawh a ngai lo. Default maximum frequency chu 400Hz a ni a, a hmangtute chuan spindle RPM mamawh angin frequency hi an siamrem thei a ni.

Single phase input leh three phase output hmanga design a nih avangin workshop leh CNC router hmangtute tan pawh a tha hle a, 110V power supply atanga three phase 110V spindle motor tlan tir a ngai a ni.

Brake Resistor inzawmna leh MODBUS485 Inbiakpawhna

He VFD hian Mach3 leh MODBUS485 communication function a support a ni. Built-in brake unit hian inverter hi brake resistor-ah direct-in a connect thei a, hei hian CNC machining application-a deceleration control leh spindle operating stability tihchangtlunna kawngah a pui a ni.

Air Volume Cooling Fan lian tak a ni

Cooling fan hian fan pangngai aiin air volume 20% aia tam a pe a ni. VFD chhunga independent heat dissipation air channel hian cooling space hran a siam a, circuit board chhunga leivut leh tui hnim lut lo turin a pui bawk.

Fault tam tak laka invenna

Inverter hian PID setting, speed tracking, multi-function relay output, multiple fault protection, multiple status feedback, torque control, leh analog setting te a keng tel a ni. Heng function te hian CNC routing, engraving, leh machining operation neih laiin VFD leh spindle motor te venhimna kawngah a pui thin.

Speed ​​hniam Rotation-ah Torque sang tak a awm

DSP vector control hian spindle motor chu speed hniam taka rotation laiin torque sang tak a nei thei a ni. Dead zone compensation leh automatic torque difference compensation hian CNC spindle application mamawh tak tak tan low frequency 0.25Hz leh 180% high torque output a nei thei a ni.

16kHz Carrier Frequency a inthlak theih bawk

Carrier frequency hi 16kHz thlenga adjust theih a ni. Automatic voltage regulation technology hian CNC machining neih laiin VFD load capacity leh spindle motor performance nghet tak a neih theih nan a pui a ni.

VFD Wiring Diagram hmanga siam a ni

VFD leh Control Board inkara Wiring Diagram

He VFD hi phase thum 110V asynchronous CNC spindle motor tan chauh hman theih a ni.

Spindle motor chu VFD-a U / V / W terminal-ah connect rawh.

Engin Nge He 2.2KW CNC VFD hi a danglam bik?

• 110V 2.2KW CNC spindle motor speed control theihna tura duan a ni.

• Pre-programmed basic parameters hian setup hun a ti tlem thei hle.

• Brake resistor connection hian deceleration control nghet zawk a support a ni.

• DSP vector control hian speed hniam rotation-ah torque sang tak a pe chhuak thin.

• Multiple fault protection hian CNC hnathawh laiin himna a ti tha hle.

• Independent cooling channel hian dust leh moisture impact a tihziaawm thei a ni.

• CNC router, CNC engraving, thinga siam, leh spindle motor system atan a tha.

Zhong Hua Jiang Brand leh thil siam chhuah dan

Huajiang hi kum 2000 khan din a ni a, CNC engraving spindle motor siam aṭangin a ṭan a, a hnuah VFD variable frequency drive leh engraving machine-ah siam a ni. Khawvel pum huap market tam zawk chhui leh tihhmasawn nan Zhong Hua Jiang brand hi kum 2018 khan din a ni.

Zhong Hua Jiang hian CNC spindle motor leh VFD product-ah hun rei tak chhung thil siamna lama tawnhriat a nei a, CNC router hmangtute, machine siamtute, distributor-te, leh international market-a B2B lei duhte tan thil a supply ṭhin.

Warranty leh Support a awm bawk

CNC spindle motor leh VFD products lama hun rei tak chhunga thil siam lama tawnhriat nei tawh Zhong Hua Jiang hian product thlan dan, wiring, setup, leh application zawhna hrang hrangah support a pe a ni. Bulk order, distributor lei duh tan, CNC spindle system matching duh tan, chipchiar zawkin min rawn biak theih reng e.

FAQ

He 2.2KW VFD hian eng spindle motor nge a hman theih?

He VFD hi phase thum 110V asynchronous CNC spindle motor tan chauh a tha a ni. Install hmain spindle motor voltage, phase, leh power te chu inverter specification nen a inmil tih finfiah hmasa phawt ang che.

He VFD hian single phase 110V hi three phase 110V ah a chantir thei ang em?

Awle. He VFD hian single phase 110V input a hmang a, CNC spindle motor inmil tur tan phase thum 110V output a pe bawk.

He CNC VFD hi pre-programmed a ni em?

Awle. VFD hi basic parameters hmanga pre-programmed a ni. User te chuan spindle speed mamawh angin frequency an siamrem thei a, default maximum frequency chu 400Hz a ni.

He VFD hian Mach3 leh MODBUS485 a support em?

Awle. He inverter hian Mach3 control leh MODBUS485 communication a support a, hei vang hian CNC router control board integration atan a tha hle.

He VFD hi brake resistor nen a inzawm thei em?

Awle. VFD hian brake unit built-in a nei a, deceleration control tihchangtlun nan brake resistor inmil takah direct-in connect theih a ni.

Eng CNC application nge he 2.2KW VFD hi hmang thei ang?

CNC router, CNC engraving machine, thinga siam CNC machine, leh spindle motor system dang, variable frequency speed control ngai te tan hman a ni tlangpui.