|
Zhong Hua Jiang chuan a rawn ti a
Zhong Hua Jiang 110V 1.5kW CNC variable frequency drive (VFD) hi three-phase 110V asynchronous spindle motor nena inmil tur atana siam a ni. Single-phase 110V, 50/60Hz power a pawm a, CNC router, engraving machine leh woodworking equipment-a variable-frequency spindle control atan three-phase 110V output a pe bawk.
Rated power 1.5kW (2HP), 0–400Hz output-frequency range, DSP vector control, MODBUS485 communication leh Mach3 control support neiin, he CNC spindle inverter hian motor control function te chu compact housing nen a thlunzawm a ni. Basic spindle parameters te chu pre-programmed a ni a; installer chuan a hnathawh hmain motor leh drive setting zawng zawng a la check vek tur a ni.
Compatibility hriat tur pawimawh: He model hi three-phase 110V asynchronous CNC spindle motor tan chauh a ni. Three-phase 220V spindle motor atana ruahman VFD aiah general substitute a ni lo.
VFD Details & Quotation dil theih a ni
110V single-phase input: Phase thum 110V asynchronous CNC spindle motor nena inmil tur a pe chhuak.
1.5kW (2HP) rated power: Drive leh motor ratings chhunga spindle motor hmanna atana siam a ni.
0–400Hz output-frequency range: Variable-frequency spindle motor hnathawhna a thlawp.
Pre-programmed basic settings: Conected spindle atana verified tur initial configuration a pe.
MODBUS485 leh Mach3: CNC control ruahmanna inmil tak nena inzawmkhawmna a thlawp.
Built-in braking unit: External braking resistor dik taka tarlan connection a support.
DSP vector control: Speed hniam taka torque-control function a pe thei.
Drive venhimna leh feedback: Fault-protection leh status function hrang hrang a awm.
Cooling design: Cooling fan leh independent heat-dissipation air channel a thlunzawm.
| Product Type | CNC Variable Frequency Drive / Spindle Motor Inverter hmanga siam a ni |
|---|---|
| Rated Power | 1.5kW / 2HP a ni |
| Input Voltage | Single-Phase 110V a ni |
| Input Frequency | 50/60Hz a ni |
| Output Voltage | Phase thum nei 110V a ni |
| Output Frequency | 0–400Hz inkar a ni |
| Motor nena inmil Motor | Three-Phase 110V Asynchronous CNC Spindle Motor hmanga siam a ni |
| Inbiakpawhna / Control | MODBUS485 a ni a; Mac3 Control Support a ni |
| Motor Control | DSP Vector Control hmanga enkawl; Speed leh Torque Function hrang hrang a awm |
| Carrier Frequency | 16kHz thlenga adjust theih a ni |
| Braking | Built-In Braking Unit hmanga pawn lam Braking Resistor hman theih tur |
| Dimensions | 90 × 118 × 150mm (3.5 × 4.65 × 5.9 in vel) a ni. |
| A rih zawng | 1.3kg (2.87lb vel) a ni. |
Commissioning hmain motor nameplate, drive ratings, cable arrangement leh control mamawh te enfiah hmasa phawt ang che. Specification tihchhuah tawhte hian output current phalsak, resistor rating emaw full terminal parameter emaw a tarlang lo va; hengte hi model documentation hman tur aangin a nemnghet tur a ni.
Basic CNC spindle parameters te hi pre-programmed a ni a, published default maximum frequency chu 400Hz a ni. Operator chuan drive controls emaw, a inmil external control system emaw hmangin output frequency a siamrem thei a ni. Motor rated voltage, current, frequency leh parameter mamawh dangte chu a nameplate leh VFD manual angin set la, factory settings chu spindle tin nen a inmil tih ngaihtuah ai chuan.
He configuration hi single-phase 110V supply tha tak nei workshop tan a ni a, chu chu three-phase 110V CNC spindle motor inmil tak hman a ngai a ni.
VFD hian MODBUS485 communication leh Mach3 nena inzawm CNC control integration a support a ni. Electrical connection leh software configuration chu controller thlan, communication setting leh VFD manual-a terminal function tarlan danah a innghat a ni. External signal connect hmain interface leh control method kha confirm hmasa phawt ang che.
Built-in braking unit chuan deceleration mamawhna hman tur atan external braking resistor inmil hman a phalsak a ni. Drive documentation atang hian resistor resistance, power rating leh wiring te thlang rawh. Braking resistor hi original product description-ah hian accessory telh anga tarlan a ni lo.
Product description tihchhuahah chuan cooling fan hian comparison fan pangngai aiin airflow 20% aia tam a pe tih a tarlang. Tin, independent heat-dissipation air channel, internal circuit board-a leivut leh tui hnim lo thleng tur tihtlem tumna a sawi bawk. Ventilation kawng chu tihbuai lohvin dah la, installation environment mamawh tarlan angin zawm rawh; he design hian waterproof emaw dustproof emaw enclosure rating a siam lo.
Original product information-ah hian PID settings built-in, speed tracking, multi-function relay output, fault-protection function tam tak, status feedback, torque control leh analog setting te a awm a. Heng function te hian drive leh machinery instruction-in a mamawh angin configure a nih chuan CNC spindle system inmil tak integration leh operation a pui a ni.
Protection functions hian electrical protection, grounding, emergency-stop ruahmanna emaw, installation leh commissioning thiam tak emaw a thlak lo.
DSP vector control, dead-zone compensation leh automatic torque compensation te hi frequency hniam zawka spindle performance puitu anga sawi a ni. Technical description hmasa berah chuan control condition tarlan hnuaiah 0.25Hz-a low-frequency operation leh 180% torque thlenga hnathawh dan a tarlang. Motor output tak tak chu motor characteristic, control setting leh thermal limits ah a innghat a ni.
Carrier frequency hi 16kHz thlenga adjust theih a ni. Drive hian original product information-a tarlan automatic voltage-regulation function a keng tel bawk. Carrier-frequency settings hian audible noise, heat generation leh drive loading te a nghawng thei a, chuvangin installation hian VFD instruction hman tur a zawm tur a ni.
A hnuaia original product illustration hian wiring reference information a pe a ni. Connection engmah siam hmain mi thiamte chuan drive bik terminal marking leh installation manual te an enfiah hmasa tur a ni. Electrical supply chu isolate la, VFD hnathawh hmain discharge fimkhurna tulte zawm rawh.
A hnuaia diagram hian VFD-to-control-board connection ruahmanna hmasa ber a tarlang a ni. Controller output signals, terminal assignment leh control settings te chu commission hmain VFD documentation nen match rawh.
Motor connection: Original product instruction-ah hian VFD-a U / V / W terminal te chu three-phase spindle motor output-te tan a ni. Heng terminal te hi incoming single-phase power terminal atan hman tur a ni lo.
Motor nena inmil: Three-phase 110V asynchronous CNC spindle motor remchang chauh hmang ang che. Motor power, rated current, frequency leh control settings te pawh VFD thiltihtheihna nen a inmil tur a ni.
He 110V CNC VFD hi CNC router, engraving machine leh thinga siamna hmanruaa hman tur variable-speed spindle system inmil tur atana ruahman a ni. CNC hmanrua distributor, machine integrator, repair specialist leh professional purchasing team te pawhin an ngaihtuah thei ang.
Product information dil hunah spindle motor-a rated voltage, phase, power, frequency leh current te hriat chian a ngai a; mains supply awmsa te; CNC controller a ni a; leh braking emaw external-control emaw mamawh eng pawh a awm bawk. Quotation sawihona atan thil lei tur beisei zat leh destination market pe rawh.
Motor Compatibility & Bulk Order chungchang sawiho rawh
Huajiang hi kum 2000 khan din a ni a, a tirah chuan CNC engraving spindle motor siamin, a hnuah variable frequency drive leh CNC engraving machine-ah te a zau chho leh a ni. Zhong Hua Jiang brand hi kum 2018 khan international market zau zawka hmasawnna atan din a ni. Company hian ram pawn lama market-ah CNC spindle nena inzawm hmanrua a supply ṭhin.
He drive hi three-phase 110V asynchronous CNC spindle motor tan a ni. Motor voltage, rated current, power leh frequency zawng zawng hi connection hmain enfiah vek tur a ni.
Awle. A electrical configuration tihchhuah tawh chu single-phase 110V input leh three-phase 110V output a ni a, hei hi spindle motor nena inmil tur a ni.
A sawi angin a ni lo. Drive hi three-phase 110V asynchronous spindle motor tan tarlan a ni. 220V spindle atan chuan VFD output voltage tling leh electrical ratings inmil tak thlang rawh.
Output-frequency range tihchhuah tawh chu 0–400Hz a ni. Spindle motor hman phalna frequency leh mechanical speed limit te chu zah tur a ni.
Awle. Basic spindle parameters te hi pre-programmed a ni a, published default maximum frequency chu 400Hz a ni. Installer chuan connected motor nena inmil turin settings a verify tur a ni a, a siamrem tur a ni.
Product information ah hian Mach3 control leh MODBUS485 communication support te a awm vek a. Wiring leh parameter setting mamawh chu CNC control board leh communication method thlan danah a innghat a ni.
Drive hian external resistor inmil tur braking unit built-in a nei niin an sawi. VFD model dik tak chu permitted resistor specification leh connection instruction te enfiah rawh.
Documentation original chuan U / V / W terminal te chu VFD motor output terminal a nih thu a tarlang a. Mi thiamte chuan installation hmain model-specific wiring diagram atang hian terminal leh protective connection zawng zawng chu an confirm vek tur a ni.
I motor nameplate information, a mamawh zat, i hman tum, CNC controller mamawh leh destination market te pe rawh. External braking emaw commissioning chungchanga zawhna bik i neih chuan telh bawk ang che.
Zhong Hua Jiang hi biak la, 110V 1.5kW CNC VFD specification, spindle compatibility leh i equipment supply emaw integration project atana lei tur mamawh te sawipui rawh.
