VFD 110V 1.5KW 2hp Ku cinca-cinca Frequency Drive CNC VFD Motor Drive Inverter Xihundzuluxi xa CNC Spindle Motor

Zhong Hua Jiang 110V 1.5KW 2HP CNC VFD Xihundzuluxi xa Xirhendzevutani xa Motor

Leswi Zhong Hua Jiang 110V 1.5KW CNC VFD inverter yi endleriwe ti-phase tinharhu 110V asynchronous CNC spindle motors. Yi hundzula single-phase 110V input kuya eka three-phase 110V output, leswi endlaka leswaku yifaneleka eka ti CNC routers, michini yo vatla, michini yo tirha hi mapulanga, na switirhisiwa swin’wana swo lawula rivilo ra spindle.

VFD yi seketela 0–400Hz output frequency, vuhlanganisi bya MODBUS485, vulawuri bya Mach3, vuhlanganisi bya yuniti ya maburuku leyi akiweke endzeni, vulawuri bya vector ya DSP, ntirho wa rivilo ro tala, na nsirhelelo wa swihoxo swo tala. Yi phurogiremiwile ka ha ri emahlweni na tipharamitha ta xisekelo ta spindle ku pfuna vatirhisi ku hetisisa ku vekiwa na ku khomixini hi ndlela leyinene.

Swihlawulekisi Swa Nkoka

• 1.5KW / 2HP CNC VFD inverter ya ti-phase tinharhu ta 110V spindle motors.

• Single-phase 110V input na three-phase 110V output.

• 0–400Hz vuhumelerisi bya frequency ya vulawuri bya rivilo ra spindle ra CNC.

• Tipharamitha ta xisekelo leti phurogiremiweke ka ha ri emahlweni leswaku ku lulamisiwa ku olova.

• MODBUS485 vuhlanganisi na nseketelo wa vulawuri bya Mach3.

• Yuniti ya maburuku leyi akiweke endzeni ya ku hlanganisiwa ka resistor ya maburuku hi ku kongoma.

• DSP vector control ya torque yale henhla eka rivilo rale hansi.

• Nsirhelelo wa swihoxo swo tala eka ntirho wa CNC lowu hlayisekeke.

• Fani leyikulu yo kufumeta na xiteji xo herisa ku hisa lexi tiyimeleke.

• Swi lulamerile eka ti router ta CNC, michini yo vatla, na tisisiteme ta spindle motor.

Tipharamitha ta Xithekiniki

• Xiendliwa: CNC VFD inverter / ku cinca-cinca frequency drive

• Matimba: 1.5KW / 2HP

• Voltage yo nghenisa: Single-phase 110V

• Voltage ya vuhumelerisi: Three-phase 110V

• Mpimo wa ku nghenisa: 50/60Hz

• Mpimo wa vuhumelerisi: 0–400Hz

• Motor lowu tirhaka: Motor wa swiphemu swinharhu wa 110V asynchronous CNC spindle motor ntsena

• Vukulu: 90 × 118 × 150mm / 3,5 × 4,65 × 5,9 wa tisentimitara

• Ndzilo: 1.3kg / 2.87lbs

Nhlamuselo ya Xiendliwa

CNC VFD leyi nga phurogiremiwa ka ha ri emahlweni leswaku yi Olovisa ku Setup

VFD yi phurogiremiwile ka ha ri emahlweni hi ti parameter ta xisekelo ta spindle, hikokwalaho vatirhisi a va lavi ku hetisa vukorhokeri byo sungula lebyi rharhanganeke va nga si tirha. Frequency yale henhla ya default i 400Hz, naswona rivilo ra spindle ringa lulamisiwa hiku tirhisa button ya frequency kumbe sisiteme ya vulawuri byale handle.

Inverter leyi yi endliwile hi single-phase input na three-phase output, leswi endlaka leswaku yiva nhlawulo lowu tirhaka eka ti workshop hiku tirhisa mphakelo wa gezi wa 110V loko yiri karhi yi tirhisa ti three-phase CNC spindle motors.

Ku hlanganisiwa ka Brake Resistor na Vuhlanganisi bya MODBUS485

VFD leyi ya CNC yi seketela vuhlanganisi bya Mach3 na MODBUS485. Yuniti ya maburuku leyi akiweke endzeni yi pfumelela inverter ku hlanganisa hi ku kongoma na resistor ya maburuku, leswi pfunetaka ku antswisa matirhelo ya deceleration na ku tshamiseka ka vulawuri bya spindle eka switirhisiwa swa michini ya CNC.

Fani Leyikulu yo Pfuxeta Vholumo ya Moya

Fan yo kufumeta yinyika kutlula 20% wa volume yale henhla ya moya kutlula ti fans leti tolovelekeke. Xiyenge xa ​​moya xo hangalasa kuhisa lexi tiyimeleke endzeni ka VFD xi pfuneta ku sirhelela bodo ya xirhendzevutani eka ntshuri na nkungu wa mati, leswi seketelaka matirhelo yo tiya eka ti workshop ta CNC.

Nsirhelelo wa Swihoxo swo Tala

Inverter yi katsa ku vekiwa ka PID loku akiweke endzeni, ku landzelerisa rivilo, vuhumelerisi bya relay bya mintirho yo tala, nsirhelelo wa swihoxo swo tala, mbuyelo wa xiyimo xo tala, vulawuri bya torque, na ku vekiwa ka analog. Mintirho leyi yi pfuneta ku sirhelela VFD na spindle motor hinkarhi wa CNC routing na engraving operation.

Torque ya le Henhla eka Rivilo ra le Hansi

DSP vector control yi endla leswaku spindle motor yi fikelela torque yale henhla hinkarhi wa ku rhendzeleka ka rivilo rale hansi. Dead zone compensation na automatic torque difference compensation swinga nyika low-frequency 0.25Hz na 180% high torque output eka switirhisiwa swa CNC spindle leswi lavaka.

Frequency ya Carrier ya 16kHz leyi lulamisiwaka

Frequency ya carrier yi lulamisiwa kufika eka 16kHz. Thekinoloji ya vulawuri bya voltage ya otomatiki yi pfuneta ku tiyisisa vuswikoti bya ndzhwalo wa VFD na matirhelo ya spindle motor leyi tiyeke hi nkarhi wa CNC machining.

Xifaniso xa Wiring xa VFD

Xifaniso xa Wiring Exikarhi ka VFD na Control Board

VFD leyi yi tirha ntsena eka ti three-phase 110V asynchronous CNC spindle motors.

Hlanganisa motor wa spindle eka ti terminal ta U / V / W eka VFD.

I Yini Lexi Endlaka Leswaku VFD Leyi Ya CNC Yi Hlawuleka?

• Yi endleriwe switirhisiwa swa 110V 1.5KW / 2HP CNC spindle motor.

• Tipharamitha ta xisekelo leti phurogiremiweke ka ha ri emahlweni ti hunguta nkarhi wo veka.

• Ku hlanganisiwa ka brake resistor swi seketela vulawuri byo antswa bya deceleration.

• DSP vector control yinyika torque yale henhla eka rivilo rale hansi.

• Nsirhelelo wa swihoxo swo tala wu antswisa vuhlayiseki bya ntirho.

• Independent cooling channel yi pfuneta ku hunguta ntshuri na ku khumbeka ka ndzhongho.

• Zhong Hua Jiang una ntokoto wa nkarhi woleha wo endla eka ti CNC spindle motors, VFDs, na michini yo vatla.

Brand na Vumaki bya le ndzhaku

Huajiang yi simekiwile hi 2000, yisungule hiku endliwa ka ti CNC engraving spindle motors naswona endzhaku yi ndlandlamuxiwa kuya eka VFD variable frequency drives na michini yo vatla. Vurhangeri bya Zhong Hua Jiang byi simekiwile hi 2018 ku seketela nhluvukiso wo anama wa makete wa matiko ya misava.

Khamphani yi na ntokoto wa vumaki eka ti motor ta CNC spindle na switirhisiwa swa VFD, ku rhumela ematikweni mambe eka timakete ta misava hinkwayo, naswona yi nyika nseketelo eka vatirhisi va michini ya router ya CNC, vaxavisi, na vaxavi va B2B.

FAQ

Hi yihi spindle motor leyi 1.5KW VFD yi fambisanaka na yona?

VFD leyi yi lulamerile ntsena eka ti three-phase 110V asynchronous CNC spindle motors. A yi fanelanga ku tirhisiwa na ti motor leti nga fambelaniki na swilaveko swa voltage, phase na power.

Xana VFD leyi yi nga hundzula single-phase 110V ku ya eka three-phase 110V?

Ina. VFD yi tirhisa single-phase 110V input naswona yi nyika three-phase 110V output eka ti CNC spindle motors leti fambelanaka.

Xana CNC VFD leyi yi phurogiremiwile ka ha ri emahlweni?

Ina. VFD yi phurogiremiwile ka ha ri emahlweni hi tipharamitha ta xisekelo. Vatirhisi va nga lulamisa frequency kuya hi spindle RPM leyi lavekaka, na default maximum frequency leyi vekiweke eka 400Hz.

Xana VFD leyi yi seketela Mach3 na MODBUS485?

Ina. VFD leyi yi seketela vulawuri bya Mach3 na vuhlanganisi bya MODBUS485, leswi endlaka leswaku yi faneleka eka tisisiteme ta vulawuri bya router ya CNC.

Xana ndzi nga hlanganisa brake resistor eka VFD leyi?

Ina. VFD yi katsa yuniti ya maburuku leyi akiweke endzeni naswona yi nga hlanganisiwa hi ku kongoma eka resistor ya maburuku leyi fambelanaka ku antswisiwa ka vulawuri bya ku hunguta rivilo.

Hi swihi switirhisiwa swa CNC leswi VFD leyi yi tirhisiwaka eka swona?

Yitala kutirhisiwa eka ti CNC routers, michini yo vatla ya CNC, michini yo tirha hi mapulanga, na switirhisiwa swin’wana leswi lavaka vulawuri bya rivilo ro cinca cinca eka 110V three-phase spindle motor leyi fambelanaka.